Rewires & New Builds in Balwyn
Licensed since 2007. Litmec Electrical takes on the substantial work in Balwyn and Balwyn North — new-build and rebuild fit-outs, full rewires, switchboard and supply upgrades.
Licensed since 2007. Litmec Electrical takes on the substantial work in Balwyn and Balwyn North — new-build and rebuild fit-outs, full rewires, switchboard and supply upgrades.
Balwyn runs on two tracks at once, and we work on both. On one side are the original interwar homes — Californian bungalows, Tudor-revival brick, solid houses on generous blocks — many still on their first switchboard and a good deal of their first wiring. On the other is the rebuild market, particularly through Balwyn North, where those same blocks are being replaced with large new two-storey houses.
Those two jobs could not be more different. The first is a rewire and switchboard upgrade on a house where the cable is perished, the fuses are rewireable and there is no earth-leakage protection anywhere. The second is a full pre-wire — designing the entire electrical layout from slab stage, getting circuits, data, lighting and EV provision into the plan before a wall goes up. We do both, and we would rather be involved early in either case.
The mistake we see most often on new builds here is under-speccing the things that are invisible at handover. Data cabling in particular — a large two-storey house with a single modem in the study will never have decent Wi-Fi upstairs, and hard-wiring it after the plaster is on costs several times what it would have during the build. The same goes for EV provision: running a cable to the garage while the walls are open is trivial, and retrofitting it is not.
We are based in Newport, which is about thirty to thirty-five minutes from Balwyn depending on the freeway and the time of day. We are straight with people about that. For planned work — a rewire, a switchboard, a renovation fit-out, lighting, an EV charger — the drive makes no practical difference to you, and we come out for jobs of any size. What we will not do is promise to be at your door in twenty minutes at midnight, because we cannot, and we would rather say so now than have you waiting.
We work across Balwyn and Balwyn North on planned jobs, and on a new build or a full rewire we are on site for an extended period anyway — the drive is irrelevant to that kind of work. For builders, we are used to hitting rough-in and fit-off dates and coordinating around other trades.
The other thing worth knowing is that we quote one number after looking at the board and the supply, not a cheap figure over the phone followed by a variation once the wall is open. On older homes especially, what is behind the plaster changes the job — and we would rather find that out before you have committed than after. Ring 0418 583 097 and we will give you a realistic answer about timing and cost.
Balwyn, Balwyn North, Deepdene and Mont Albert. We also work through Camberwell, Kew, Box Hill, Doncaster. Our home patch is the inner west — Newport, Williamstown and Yarraville. All Melbourne services →
Yes, and they are a good fit for us. We handle the full electrical fit-out from pre-wire at frame stage through to fit-off and handover, and we coordinate with your builder on rough-in dates. Getting involved before the plans are finalised gives you a far better result than being handed a fixed layout.
We are based in Newport, about thirty to thirty-five minutes from Balwyn depending on traffic, and we take on planned work of any size. On a rewire or a new build we are on site for days or weeks at a stretch, so the distance genuinely does not affect the job. We do not promise rapid emergency callouts this far east.
More than the builder allows for. A large two-storey house needs hard-wired data points and ceiling-mounted access points, not a single modem in the study. Running it during the build is inexpensive; retrofitting it through finished plaster is several times the cost and never as tidy.
Yes. Running a suitable cable to the garage during construction, and leaving capacity at the board, costs very little at that stage. Retrofitting the same cable later means chasing walls or running surface conduit. It is one of the cheapest pieces of future-proofing available.
With an assessment of the wiring and the switchboard, so you know what you are actually dealing with. Homes of that age commonly have perished rubber-insulated cable, rewireable fuses, unearthed lighting circuits and an asbestos-based backing board. We give you a clear picture and a staged plan rather than an alarming lecture.
Where the load justifies it, yes. Large two-storey homes with ducted air conditioning, induction, heat pump hot water and EV charging can genuinely warrant three-phase. We work out the demand properly first, because it is a real cost and not every home needs it.
Tell us about your Balwyn project and we'll get back to you quickly with a clear, no-obligation quote.